How To Repair Dashboard Lights In 2006 Silverado 1500

Vehicle dashboard lights assist the driver in monitoring the various gauges of their car. These of import lights include the speedometer, the fuel and temperature gauges amid others. Having these lights work properly is particularly useful when driving at dark.

Broken dashboard lights can leave you clueless to whether your vehicle is experiencing engine problems, such as running out of gas or overheating, oft until it is too late. Therefore it is important to have your dashboard lights working properly.

If you are experiencing your dash lights not working, there are a few things we can practise to get them working on your own that can easily exist performed at abode.

Part i of 3: Test the dimmer switch

The dimmer switch may have been pressed by accident or adjusted by another commuter of the vehicle causing the dashboard lights to become tedious or switched off.

Step ane: Locate the dimmer switch. Offset with locating the dimmer switch for the dashboard lights.

• Tip: If you are having difficulty locating it, refer to your vehicle's owner manual.

Stride two: Adjust the dimmer switch. After locating the dimmer switch, turn the key to the 2d position and plough on the headlights. Printing the switch and see if the dashboard lights become brighter.

If the dashboard lights practise non come up ane fifty-fifty after adjusting the dimmer switch, the dashboard light fuses may have blown.

Role of 2 of three: Check and supersede fuses

Materials Needed

• Fuse puller or needle nose pliers
• Replacement fuses

Pace 1: Locate the fuse for the dashboard lights. This fuse will be located within 1 of the fuse boxes for the vehicle.

The fuse boxes may be hidden under the hood near the engine or tucked away under the dashboard. Refer to the owner'due south manual of your car if you lot are having trouble locating the fuse.

• Annotation: When removing fuses from the fuse box, always have the primal turned to the zero position on the ignition. This cuts the power to most fuses in the fuse box, making information technology safe to service them.

Step 2: Remove and inspect the fuse. Apply a fuse puller or a pair of needle nose pliers to remove the dashboard light fuse and visually inspect it for any damage.

Step 3: Supercede damaged fuses. If the fuse is obviously damaged or faulty, replace it with a new fuse of the same type and amp rating.

Starting time your motorcar and bank check again to run across if the dashboard lights are performance properly.

Part of iii of 3: Check the gauge cluster

If your dashboard lights are even so non working or if one or more bulbs in the gauge cluster are not working, remove the gauge cluster from the dashboard and check the electrical connections and bulbs.

Materials Needed

• Fuse puller or needle nose pliers

• Screwdriver or a small ratchet with a 7mm or 8mm socket

• Note: The post-obit steps are a general guide to removing the gauge cluster from the dashboard for servicing. Some of these steps or the tools needed can vary from i manufacturer to another, and then information technology is recommended that you refer to your vehicle's service manual for the exact procedure for your vehicle.

Step 1: Remove the trim around the gauge cluster. Remove the beautification trim panel from around the the gauge cluster past either popping the mounting clips open or by loosening the mounting screws that attach it to the dashboard.

This console can be removed with a screwdriver or a small ratchet with a 7mm or 8mm socket.

Step ii: Remove the fasteners. With the gauge cluster now exposed, locate the fasteners, loosen and remove them using the appropriate tools.

Step three: Remove the gauge cluster. Unplug the multiple electrical connectors that attach the judge cluster to the wiring harness. Take care to disconnect all connectors and then remove it completely from the dashboard.

Step 4: Remove the bulb socket. With the gauge cluster removed, yous will see blackness, grey, red or blue bulb sockets on the back. Y'all tin hold a socket, twist it to take it out, and inspect each lite bulb for damage.

Step 5: Replace broken bulbs. If a bulb is cleaved or faulty, supersede information technology and install the socket back into its cavity.

• Tip: If burnt out bulbs are constitute in the judge cluster, it'due south a good idea to change all the bulbs. This will ensure y'all don't have to do this once again in the almost future.

Step 6: Reconnect the guess cluster. Subsequently inspecting and replacing bulbs every bit needed, reconnect the electrical connectors to the approximate cluster and slide it back into its cavity.

Secure the estimate cluster with its fasteners and remember to re-install the adornment trim panel too.

Pace 7: Exam the lights. Switch on your car and check to see whether your dashboard lights are working properly.

If the dashboard lights are still not illuminating or if you don't feel comfy attempting this process, enlist the services of a certified mechanic to supersede whatever blown fuses and supervene upon the light bulbs for you.

The statements expressed above are only for advisory purposes and should exist independently verified. Please encounter our terms of service for more details

Source: https://www.yourmechanic.com/article/how-to-repair-dashboard-lights-by-rocco-lovetere

Posted by: knoxwhadn1945.blogspot.com

Share this post